The five mistakes that cost homeowners their Ontario heat pump rebate are installing before the program approves the application, buying a standard unit instead of a cold climate model, using a contractor who is not on the program's list, replacing an existing heat pump, and missing paperwork such as the sizing form or the oil tank attestation. Every one of them comes straight from the Home Renovation Savings rules, and each one is avoidable before the work starts. 1
See what your home gets, in about a minute.
Check my rebateMistake 1: Installing before the program approves it
This is the one that cannot be fixed afterward. The program's heat pump page says pre-approval is mandatory and that installations done before approval are not eligible for rebates. 2
The requirements say the contractor and the homeowner must receive the program's written approval of the pre-installation application before the equipment goes in. If the application is not approved, the participant is not eligible for the rebate. 1
The fix: ask your contractor for the approval in writing and do not book an install date until you have it. The pages we read mention no exception for an emergency replacement, so ask the program before you act if the furnace has already failed.
Mistake 2: Buying a standard heat pump
Only cold climate air source heat pumps and ground source heat pumps are on the rebate list. A standard air source heat pump is not eligible. 2 The cold climate model must be an active listing on Natural Resources Canada's eligible product lists, and the whole system must sit under one AHRI number. 1
The program also sets a performance floor. The unit needs a heating COP of at least 1.8 at -15°C and must keep at least 70% of its rated capacity at that temperature compared with 8.3°C. 1 Ductless and mini-split systems qualify when they meet the same cold climate test and the system can heat the whole conditioned space, basement included.
The fix: ask the contractor for the model and AHRI numbers and confirm both against the NRCan list before you sign. Our cold climate guide explains the difference.
Mistake 3: Hiring a contractor who is not on the list
The work must be done by a contractor on the program's Participating HVAC Contractor List. 1 The program's help page says the contractor must be registered and listed before you proceed with the installation. 3
The minimums for the list are specific. A contractor needs a valid Ontario business licence, at least two consecutive years of heat pump business in Ontario and at least one year of preventative maintenance and warranty service. Technical requirements include a 313D or 313A Air Conditioning Systems Mechanic licence and valid TSSA registration. 1
The fix: use the list the program emails you after the eligibility form. A tradesperson who is not on the list can do good work and still leave the job ineligible. If you would rather skip the searching, we pass your request to one listed installer.
Mistake 4: Replacing an existing heat pump
Home Renovation Savings pays for a first heat pump. A home with an existing heat pump system used for space heating is not eligible, and replacing one does not qualify. 1 The program's help page says the same: the heat pump must be a first-time installation of a space heating heat pump system. 3
Three related rules catch people out. Another Enbridge, Save on Energy or Government of Ontario incentive on the same equipment disqualifies it from this rebate. 1 A new build must have been occupied for at least six months before it qualifies, and existing homes are not affected by that rule. And each home receives one rebate in total, even if you install several outdoor units. 1
The fix: if a heat pump of any kind already provides space heating, the home is out. If you are unsure whether an existing unit counts, ask the program before you spend anything.
Mistake 5: Missing paperwork, the sizing form and the tank step
The pre-installation application has several required pieces: an itemized work order, photos of the existing heating system and nameplates, your signed participant agreement and an NRCan sizing tool form for each outdoor unit. 1
The sizing form matters more than it looks. In an oil, wood or electrically heated home, only NRCan sizing options C and D qualify, which means the heat pump has to carry most or all of the heating. Gas and propane homes can use options A to D. 1 A contractor who sizes the unit mainly for cooling can leave an oil or electric home out of the program.
Oil and propane homes add the Oil/Propane Tank Removal Attestation Form. For oil, you must switch to the heat pump and work with a TSSA-registered contractor to maintain, empty or remove the tank. 1 A tank taken out of use must be emptied, and larger and underground tanks have extra rules. 4
After the installation, the contractor has 30 days to submit the post-installation application with the final itemized invoice and photos of the installed equipment. 1
The fix: ask the contractor for a checklist of every document, and ask who is responsible for each. Keep your own copies. In Woodstock, with a January design temperature of -19°C, the sizing form deserves a close look. 5
Why these rules are strict
The rebate is paid after the work is done, and the program decides eligibility from the documents your contractor submits. 1 The two applications are the whole record. A missing photo, an unsigned agreement or an unlisted model gives the reviewer nothing to approve.
A cold climate heat pump for a 3 ton house in an oil or propane home earns $3,750 under the program's own example, and up to $7,500 at 6 tons. 1 That is enough money to justify an hour of checking.
Not every mistake is yours to make. The contractor files the applications, so ask them early which of these five they check on every job.
Before you sign anything
- Confirm the contractor is on the participating list.
- Confirm the model is a cold climate unit and note its AHRI number.
- Check that the home has no existing heat pump.
- Get the sizing option in writing, and for oil, wood or electric homes confirm it is C or D.
- Do not install until you hold the written approval.
For the full list of steps, see the Ontario rebate guide, or run your home through the rebate checker.
See what your home qualifies for
Seven questions, about a minute, with the rules for your fuel.
Common questions
Can I apply for the heat pump rebate after the install?
No. The program says installations done before approval are not eligible for rebates. The contractor applies first and you wait for written approval. 2
Why was my heat pump rebate denied?
The rules support a few reasons: installation before approval, a standard instead of a cold climate unit, a contractor not on the list, a home that already had a heat pump, or missing paperwork. The program's decision letter is the only authority on your own case.
Does a mini-split qualify for the Ontario rebate?
Yes, when it is a cold climate model on the NRCan list, all components sit under one AHRI number and the system can heat the whole conditioned space, basement included. 1
Who submits the rebate paperwork?
Your contractor submits both the pre-installation and the post-installation applications. You sign the participant agreement and, for oil or propane homes, the tank attestation. 1