There is no single answer. We found no official Ontario or federal rule that says a heat pump needs a 100 amp or a 200 amp panel. What decides it is the electrical requirement on the unit's spec sheet, the load the house already carries, and whether the system has electric backup heat strips. Ask the installer for a written load calculation in the quote, and have any electrical work done by a licensed electrical contractor.
See what your home gets, in about a minute.
Check my rebateWhy nobody can give you a number
You will hear "you need 200 amps" from some sellers and "100 is plenty" from others. Neither is a rule we could find in any official source we opened. The Home Renovation Savings requirements say only that the heat pump and ductwork must comply with all applicable laws, building codes and guidelines, and any additional permitting requirements.1
That sentence sends you to the electrical code and your own house. It does not hand you an amperage.
So this article doesn't give one either. Any figure quoted without a calculation behind it is a guess.
The three things that decide it
The unit's spec sheet
Every outdoor unit carries electrical requirements, usually listed as the breaker or circuit size it needs and the current it draws. Those go on the manufacturer's spec sheet and the unit's nameplate. A small ductless unit and a large ducted unit are different loads, so the answer for your neighbour's house may not be yours.
What the house already uses
A panel is shared. The heat pump adds to a service that already feeds an electric range, a dryer, a water heater, a well pump or a barn. A house on propane or oil heat may be using very little for heating today. A house on electric baseboard already has a big heating load on the panel, and a heat pump will usually replace some of it.
Backup heat strips
Some ducted systems add electric heat strips as backup for the coldest hours. Strips sized to carry the whole house add a large load to the panel. The program allows electric resistance backup in oil and electric homes, and in wood homes the existing wood or electric heat can stay as backup.1 Choosing a different backup, such as a furnace or a woodstove, changes what the panel has to carry.
Our hybrid heat article explains the furnace option, and the wood stove article covers the stove.
Ask for a load calculation in the quote
A load calculation adds up what the electrical service has to carry once the new equipment is in. Ask the installer or their electrician to put the result in writing, with these items:
- The spec sheet for the outdoor unit and the air handler or furnace.
- The size of the existing service, read from the main breaker.
- Whether backup heat strips are included, and their size.
- Whether the panel needs an upgrade, with the cost shown as its own line.
The last line matters for comparing quotes. One installer may price a panel upgrade at $0 because they assume it is not needed, while another includes it. Ask both to show their working. Our running costs page will help you compare the long-run price once you have a real quote.
Who does the electrical work
Panel upgrades and new circuits are electrical work, and electrical work should go to a licensed electrical contractor. Some heat pump installers have electricians on staff and others bring in a partner. Ask which applies to your quote.
Ask your installer who arranges any electrical permit and how the inspection gets booked, and get that answer in writing with the quote.
The program separately requires HVAC contractors to hold a valid TSSA registration and a residential air conditioning licence (313D or 313A for cold climate air source heat pumps).1 That covers the heat pump itself. Your electrician handles the panel.
Questions to settle before you sign
- What is the electrical requirement of the specific unit you are quoting?
- What is my service size today, and what does the load calculation show?
- Is a panel upgrade needed? If yes, who does it and what does it cost?
- Are backup heat strips included, and how many?
- Who arranges any permit and inspection?
A quote that cannot answer these is incomplete. Our rebate checker is a good first step, and the installer we refer you to will take it from there. We refer you to one participating contractor and don't install or sell equipment ourselves.
See what your home qualifies for
Seven questions, about a minute, with the rules for your fuel.
Common questions
Do I need a 200 amp panel for a heat pump?
Maybe. We found no official rule that sets 100 or 200 amps. It depends on the unit's electrical requirements, what your house already uses and whether electric backup heat is included.
Can a heat pump run on a 100 amp panel?
Sometimes. A load calculation for your house is the way to find out. Ask your installer to provide one in writing.
Who should upgrade my electrical panel?
A licensed electrical contractor. Ask your heat pump installer who does the electrical work and who arranges any permit.
Does the rebate cover a panel upgrade?
The program's rebate is calculated on the heat pump's rated heating capacity, per ton, up to $7,500 for propane, oil, wood and electric homes and up to $2,000 for gas homes.1 Ask the program or your installer before assuming electrical work is covered.